bopschicago.blogg.se - Crochet chart x-stitch

#Crochet chart x stitch code#

r if reading is permitted, - if it is not.The third set represents the others class.Įach of the three characters represent the read, write, and execute permissions: The second set represents the group class. The remaining nine characters are in three sets, each representing a class of permissions as three characters. The first character indicates the file type and is not related to permissions.

You should always make a backup of this file before you start making changes. htaccess by adding # to the beginning of the line. htaccess file you can comment that specific line in the. If you would like to check a specific rule in your. htaccess file, there may be rules that are conflicting with each other or that are not allowing an IP address access to the site. This may be related to an account level suspension as a result of abuse or a violation of our Terms of Service. Note: If the permissions are set to 000, please contact our support team using the ticket system. (See the Section on Understanding Filesystem Permissions.) The server also expects the permission mode on directories to be set to 755 in most cases. The server generally expects files such as HTML, Images, and other media to have a permission mode of 644. The server you are on runs applications in a very specific way in most cases. If you have made changes to the file ownership on your own through SSH please reset the Owner and Group appropriately. The server generally expects files and directories be owned by your specific user cPanel user. Some of these are easier to spot and correct than others.

#Crochet chart x stitch code#

Attach the tassels to each corner of your pillow cover and weave in the ends.There are a few common causes for this error code including problems with the individual script that may be executed upon request.

Repeat Steps 1-8 till you have 4 tassels.

Now trim your tassel approximately 3″ down from where you just wrapped the yarn around.

Do this about 5 times and then thread the end onto your needle and insert it under the wraps from the top and pull through.

To hide the knot, take one yarn tail and wrap it around the tassel where you just tied it.

Flip the tassel over and double knot the ties. Place the tassel on top with the piece of yarn approximately 3/4″ to 1″ down from the top of the tassel and tie tightly. These will be the ties you use to attach the tassel to the pillow.

Remove the yarn from the cardboard and pull the yarn ties tight and double knot.

Insert the needle under the yarn wraps and pull it to the top of the wraps and tie in a loose knot.

Cut a 30″ piece of yarn, fold in half, and thread on your needle.

Wrap the yarn around the cardboard 40 times.

We will be wrapping the yarn around the long side. This creates a faux third SC for this corner.

Finish with an SSCF to the very first SC.

This will create the second stitches for that corner.

Place the last SC in the same space as the very first SC stitch.

Place 3 SC in the first stitch of the top edge, then continue to SC 68 stitches across the top until you reach the last stitch, where you will place the 3 SC for that corner.

This will complete the three (3) SC for this corner. Now place one more SC in the same stitch space.

SC into the same space as the last SC from attaching the small back piece, going through the front cover, small back piece, and large back piece.

Flip the cover back over so the front cover is facing up.

Place either stitch markers or scrap pieces of yarn around the edge to keep the piece in place.

Lay the large back piece over the front cover (making sure the buttonholes are at the bottom.).

Flip the cover back over so the front cover is face down.

I want everyone to enjoy making this pattern, so don’t hesitate to contact me if you have any questions or problems along the way.

You can also send me a message on Facebook through the Chain 8 Designs page. If you have any questions about this pattern, please don’t hesitate to e-mail me at Put the pattern name as the subject line and I will get back to you as soon as I can.If you know that your pillow form is on the fuller side, you might want to go up a hook size to accommodate that. For my final pillow cover, I used a moderately stuffed pillow form that measured 18″ x 18”, and the cover had a nice snug fit. How your cover fits will depend on your individual pillow forms.Not everybody’s tension is the same and not all worsted weight yarn is created equal, and both can affect the overall size of your finished project. Make sure to complete the gauge swatches before you begin.There are notes and suggestions to help you along the way.